Machinery ยท Used combine guide
Case 2188 Combine: Specs, Years Made and Running Costs
The Case IH 2188 Axial-Flow combine was built from 1995 to 1998, with a Cummins 6TA-830 engine of about 276 hp. Here are its sourced specs, what changed in the 2100 series, how to check a used one, how to measure grain loss behind it and what owning one costs against hiring.

Key takeaways
- Konedata dates the Case IH 2166, 2166E and 2188 Axial-Flow combines to 1995-98.
- RitchieSpecs lists a Cummins 6TA-830 engine of about 276 hp and an operating weight of about 20,944 lb for the 2188.
- The 2100 series brought a centre cab with armrest controls, load-sensing hydraulics, header height memory and faster unloading (Konedata).
- Two corn kernels per square foot equal about one bushel per acre of loss (Iowa State University Extension); four soybeans per square foot do the same (NDSU).
- Texas A&M’s 2026 survey puts average per-acre custom combining charges at US$31 to US$40, before hauling.
In this article
- Case 2188 combine at a glance
- What years was the Case 2188 made
- Five features that set the 2188 apart
- Buying a used Case 2188: a step-by-step check
- What it costs to run an older combine
- How to measure harvest loss behind a 2188
- Using a 2188 with modern farm data tools
- Is a Case 2188 still worth running
- FAQ
The Case IH 2188 is a rotary Axial-Flow combine that Case IH built from 1995 to 1998, as the largest model in the 2100 series beside the 2166. Spec guides list a six-cylinder Cummins 6TA-830 engine of about 276 hp, an operating weight near 20,900 lb and a hydrostatic drive. Today the case 2188 is a used machine, so the real questions are what it can still do, what it costs to run and how to keep its grain loss low.
This guide gives the specs with their sources, the changes that made the 2100 series different from earlier Axial-Flow models, a check-list for buying one, field tests for harvest loss and a calculator that compares running your own older combine with hiring a custom operator.
Case 2188 combine at a glance
The table brings together the figures that sellers and buyers ask about most. Spec sites copy data from older brochures, so small differences between listings are normal. Check the serial plate and the records of the machine in front of you.
| Item | Case IH 2188 | Source |
|---|---|---|
| Years built | 1995 to 1998 | Konedata |
| Series | 2100 series Axial-Flow (2144, 2166, 2166E, 2188) | Konedata |
| Engine | Cummins 6TA-830, 6 cylinders, 506.5 cu in | RitchieSpecs |
| Rated power | About 276 hp | RitchieSpecs |
| Operating weight | About 20,944 lb without header | RitchieSpecs |
| Drive | Hydrostatic, 3 gears, up to 12.5 mph | RitchieSpecs |
| Threshing width | About 107.9 in | RitchieSpecs |
| Size | 22.25 ft long, 11.46 ft wide, 12.96 ft to cab top | RitchieSpecs |
Power ratings vary between listings. Some used-equipment ads quote 260 hp, and Konedata, which draws on brochures, lists 280 hp (DIN). The 276 hp figure is what RitchieSpecs lists for the Case IH 2188, so we use it here as a guide value, not as a tested number.
What years was the Case 2188 made
The Finnish machinery database run by Koneviesti dates the Case IH Axial-Flow 2166 and 2188 to 1995-98. The same entry says Axial-Flow combines had changed little in their first 18 years before the 2100 series arrived in 1995. That makes every 2188 on the market today 28 to 31 years old.
Age matters for two reasons. Parts for the cab, electronics and hydraulics may come from the used or remanufactured market. On the other hand, the price of a combine this old is low, so ownership costs per acre can be low too. The section on costs below shows how to weigh that.
How the 2188 fits in the Axial-Flow line
Case IH says in its history of the Axial-Flow design that its first yield monitors came in 1994, auto guidance in 2006 and Harvest Command automation in 2019. The 2188 sits at the start of that path. It came when yield monitoring was new, long before factory auto guidance. Today’s Axial-Flow 260 series is rated at 402 to 550 hp with grain tanks of 315 to 410 bushels, so a 2188 is a much smaller machine than a current class 7 to 9 combine.
Five features that set the 2188 apart
The old version of this page listed “power features” with invented percentages. Here are five real features of the 2100 series, taken from the Konedata entry and the spec data above, with what each means on a working farm.
1. A single rotor with proven dimensions
The 2188 keeps the single longitudinal rotor that defines every Axial-Flow combine. Konedata notes that the rotor and threshing dimensions did not change with the 2100 series. For a buyer, that means the threshing system is well known to dealers and mechanics, and rotor parts, rasp bars and concaves are still sold by dealers and aftermarket suppliers; check availability locally.
Best for: growers who harvest corn, soybeans and small grains and want gentle threshing that is simple to set.
2. A new centre cab with armrest controls
The most visible change in 1995 was a new cab in the centre of the machine. Most controls moved onto the armrest and the seat gained air suspension. On long harvest days that layout helps the operator see the header and reach the main controls without twisting.
Best for: farms where one person runs the combine for many hours a day.
3. Load-sensing hydraulics and a stronger drive
Konedata says the hydraulic system was rebuilt around a load-sensing pump and the power train was reinforced. The 2188 has about 276 hp from its Cummins six. Check the hydrostatic pump, final drives and rotor gearbox closely on any used unit, because these are the costly parts.
Best for: heavier crops and hilly fields where the drive and header work hard.
4. Header height memory and auto float
After a turn, the 2100 series could return the header to its last cutting height from memory, and automatic flotation was offered as an option. These features help keep stubble even and cut down on missed heads in soybeans and small grains. Find out whether the machine you are looking at has the option fitted and working.
Best for: low-cut crops such as soybeans, where header height has a big effect on loss.
5. Faster unloading
The new series emptied its grain tank faster, and the auger speed control was standard. A quicker unload means less time stopped at the cart and more time cutting during a short harvest window.
Best for: operations that run a grain cart and want to keep the combine moving.
Buying a used Case 2188: a step-by-step check
A combine this age can be a sound buy, or a money pit. Work through these steps before you agree a price. If you are not sure about any item, ask a dealer mechanic for a pre-purchase check.
- Confirm the model and year. Read the serial plate. Make sure it is a 2188, not a 2166 with a 2188 decal, and match the year to the 1995-98 range.
- Read the hours. Ask for both engine hours and rotor (separator) hours. Rotor hours tell you more about wear in the threshing system.
- Look inside the rotor area. Check rasp bars, concaves, cage vanes and the rotor itself for wear, cracks and past welding.
- Test the drive. Drive the machine loaded if you can. Listen for whine from the hydrostatic system and check that it pulls evenly in all three gears.
- Check the engine. Look for blow-by, oil leaks, coolant in the oil and smoke under load. Ask for oil analysis records.
- Check the electronics. Test the header height memory, monitors and any yield monitor that has been added.
- Ask for records. A folder of receipts and service records is worth money. So is a record of the acres harvested each year.
- Price the header separately. A grain platform or corn head can change the total cost a lot. Check its condition on its own.
Asking prices online are dealer or private asks, not sales. Auction results are a better guide to what buyers really pay. Write down the date of every price you compare, because older combine prices move with grain prices and the season.
What it costs to run an older combine
Older combines cost less to own, but often more to repair. A December 2025 farmdoc daily analysis of crop machinery costs found an average machinery cost of US$185 per acre for corn on farms with under 250 acres in 2024, and US$178 on farms with over 1,000 acres. For soybeans the figures were US$122 and US$108. Those costs include all machines on the farm, not only the combine.
Chart
Machinery cost per acre by farm size, 2024
US$ per acre, all crop machinery, farms grouped by acres of the crop
The same authors make a point that matters for anyone running a 2188. A farm with older machines has lower depreciation and interest on that machinery, so its cost per acre can look low. Whether that lasts depends on repair bills and on how often the old machine breaks down in the middle of harvest.
Mississippi State University Extension explains how to split farm machinery costs into two groups. Ownership costs cover depreciation, interest, taxes, insurance and housing. Operating costs cover repairs, fuel, lubrication and labor. Use your own records for both before you decide to keep, replace or hire.
Owning versus hiring a custom operator
Custom combining is the main alternative to owning. The Texas A&M AgriLife custom rates survey (2026) reports statewide average per-acre charges of US$34.73 for corn, US$39.67 for soybeans, US$32.35 for grain sorghum and US$31.30 for wheat and other small grains. Those are per-acre parts of a rate that often adds hauling per bushel and sometimes an overage charge on high yields, so the full bill is higher.
Rates differ by state and region, so ask local operators for quotes. The calculator below lets you put your own numbers side by side.
Chart
Custom combining charge per acre in Texas
Statewide average per-acre part of combining and hauling rates, US$, 2026 survey
Try the numbers for your own farm below.
Calculator
Own an older combine or hire a custom operator?
Enter your acres, yearly ownership cost, running cost and a local custom rate.
- Cost per acre to own and run: $35 US$/ac
- Value of extra grain loss: 0 US$
- Cost to hire: 17,500 US$
Example values only, set near break-even; they are not benchmarks. Use your own records and a quote from a local operator (example, use today’s price). Ownership cost covers depreciation, interest, taxes, insurance and housing; running cost covers repairs, fuel, lubrication and labor (Mississippi State University Extension). The loss line uses two corn kernels per square foot = one bushel per acre (Iowa State University Extension). Get advice from your accountant or lender before buying.
How to measure harvest loss behind a 2188
Every combine leaves some grain in the field. The useful question is how much, and whether a setting change can cut it. On a machine close to 30 years old, worn parts can push loss up without the operator noticing.
The rule used by extension services is simple. Iowa State University Extension states that two corn kernels per square foot, or one three-quarter pound ear in 436 square feet (0.01 acre), equals one bushel per acre of loss. It adds that over half of corn harvest loss happens at the corn head, where rear loss sensors cannot see it, and that machine loss in corn that stands well should be no more than one bushel per acre.
For soybeans, North Dakota State University Extension uses four seeds per square foot as one bushel per acre of loss. Its steps are a good field routine:
- Combine at your normal speed and settings for at least 100 feet.
- Stop the header and threshing unit and back up 10 to 20 feet.
- Lay a one-square-foot frame on the ground in 4 to 6 places, behind the machine and in front of it.
- Count the kernels or seeds in each frame and find the average.
- For corn, also count whole ears on 1/100 of an acre.
- Take the count in front of the combine (pre-harvest loss) away from the count behind it. The difference is the machine loss.
The University of Wisconsin corn team gives benchmarks in its grain harvesting guide: an acceptable machine ear loss of 0 to 1.0 bushels per acre, and a typical ear loss of 0.6 to 2.5 bushels per acre. It says keeping total loss under half a bushel would place you in the top ten percent.
Settings that cut loss on an Axial-Flow
- Ground speed: go slower when ears drop or the head is shelling.
- Corn head: set the deck plate gap so ears do not touch the stalk rolls, and match roll speed to ground speed.
- Rotor speed and concave: set only fast and close enough to thresh cleanly. Too much cracks grain, too little leaves it in the head.
- Fan and sieves: adjust so clean grain does not blow out of the back.
- Re-check: test again after each change and when the crop or moisture changes.
Grain loss data is only useful if the yield data is right. Many 2188 combines run add-on yield monitors, and those need calibration with weighed loads each season. Skipping calibration in a busy harvest gives yield maps that mislead later decisions.
Chart
Corn harvest loss benchmarks
Bushels per acre left in the field
Using a 2188 with modern farm data tools
An older combine can still feed a modern farm record. Add-on yield monitors and GPS receivers can be fitted to many older machines; ask your dealer which kits suit a 2100 series combine. Pair the yield maps with crop health maps taken through the season, and the weak parts of each field show up in both.
Satellite crop monitoring helps here. The Farmonaut Satellite + AI Farm Monitoring System shows vegetation index maps of each field through the season on web, Android and iOS, so you can see which zones were stressed before harvest and compare them with the yield map. For harvest planning across several machines, see our page on fleet management for farm machinery.
For a wider look at newer harvest technology, read our guide to smart harvesting tech advances.
โถ A tutorial on viewing satellite crop health maps of your own fields in the Farmonaut web app. ยท 8:43
Is a Case 2188 still worth running
For many small and mid-size farms the answer can be yes. The 2188 has a proven rotor, a strong engine for its size and a centre cab with armrest controls that was new in 1995. It suits farms that harvest a few hundred acres a year, have a good mechanic close by and keep spare parts on hand.
It is less suited to large farms that need high daily capacity or factory automation. A current Axial-Flow 260 series combine is rated at 402 to 550 hp, and features such as auto guidance and Harvest Command did not exist when the 2188 was built. On those farms, the time lost to a breakdown can outweigh the saving in ownership costs.
Run the numbers both ways. Use your own repair records, a realistic count of acres and local custom rates. Then decide whether to keep the old machine, trade up or hire. For tax, loan and insurance choices, get advice from your accountant or farm lender.
Related pages on our site: carbon footprint tracking, crop loans and insurance data, product traceability, satellite and weather API docs, farm monitoring app.
โถ How new farm technology, from self-driving tractors to data tools, changes work, money and jobs in rural towns. ยท 3:50
FAQ
When was the Case 2188 combine made?
The Koneviesti Konedata database dates the Case IH 2166 and 2188 Axial-Flow combines to 1995-98. They formed the 2100 series, which brought a new centre cab and load-sensing hydraulics to the Axial-Flow line.
How much horsepower does a Case 2188 have?
RitchieSpecs lists about 276 hp from a Cummins 6TA-830 six-cylinder engine with 506.5 cubic inches. Some used-equipment listings quote 260 hp, so check the plate and records of the machine you are buying.
What is the difference between the 2166 and the 2188?
Both share the 2100 series design and the single rotor. Konedata’s entry covers the 2166, the 2166E and the 2188, and notes a 180 hp 2144 was also sold in America. The 2188 was the higher-capacity model; compare the engine plate and spec sheet of each machine you look at.
How much grain loss is normal behind a combine?
The University of Wisconsin gives 0 to 1.0 bushels per acre as an acceptable machine ear loss in corn and 0.6 to 2.5 bushels per acre as a typical ear loss. In corn, two kernels per square foot equal about one bushel per acre.
Is it cheaper to own an old combine or hire custom combining?
It depends on your acres, repair bills and local rates. The 2026 Texas A&M survey puts average per-acre combining charges at about US$31 to US$40 before hauling. Spread your yearly ownership costs over your acres, add operating costs per acre and compare.
Which crops can a Case 2188 harvest?
With the right header and settings, Axial-Flow combines of this age harvest corn, soybeans, wheat, barley, sorghum and other small grains. Set the rotor speed, concave and sieves for each crop and test loss in the field.
Farmonaut crop monitoring
See your fields before harvest
Draw your fields once and Farmonaut shows satellite vegetation maps through the season on web, Android or iOS, ready to compare with your yield map.

Sources
- Koneviesti Konedata, Case IH Axial-Flow 2166-2188 (model entry, years 1995-98): koneviesti.fi
- RitchieSpecs, Case IH 2188 Combine specifications: ritchiespecs.com
- Case IH, The Strength of the Axial-Flow Legacy (Farm Forum): caseih.com
- Case IH, Axial-Flow 260 Series combines (product page): caseih.com
- farmdoc daily, Crop Machinery Costs (University of Illinois, December 2025): farmdocdaily.illinois.edu
- Purdue Center for Commercial Agriculture, Machinery Cost Benchmarks for Corn & Soybeans (December 2025): ag.purdue.edu
- Mississippi State University Extension, Farm Machinery Cost Calculations: extension.msstate.edu
- Texas A&M AgriLife Extension, Texas Custom Rates Survey 2026: agecoext.tamu.edu
- Iowa State University Extension, Minimize amount of corn left on the ground behind the combine (Mark Hanna, 2010): crops.extension.iastate.edu
- North Dakota State University Extension, estimating corn and soybean harvest loss: ndsu.edu
- University of Wisconsin Corn Agronomy, Grain Harvesting: corn.agronomy.wisc.edu
Discussion
Questions, corrections or field experience? Share them below. First-time comments are reviewed before they appear, and your email is never published.
No comments yet. Be the first to add a question or your experience.




Client · Oregon, USA · Gold
Exploration consultancy · South Africa · Gold
Licence holder · Niger · Gold
Licence holder · Nigeria · Gold + lithium
Client · Tanzania · Gold
Client · Somalia · Gold
Client & affiliate partner · Ghana · Gold